|
sungam
Oct 24, 2008, 5:00 PM
Post #26 of 36
(860 views)
Shortcut
Registered: Jun 24, 2004
Posts: 26804
|
the_climber wrote: You know if you just had one made custom you wouldn't have to file the bar 2 to 3 hours per evening for the next 2 and a half weeks... You realize this right? I dunno anyone who can do that. You really think it'll take that long? I havn't bought anything yet, so if you could suggest someone who could make one, that would pretty much rock.
|
|
|
|
|
the_climber
Oct 24, 2008, 5:09 PM
Post #27 of 36
(857 views)
Shortcut
Registered: Oct 9, 2003
Posts: 6142
|
sungam wrote: the_climber wrote: You know if you just had one made custom you wouldn't have to file the bar 2 to 3 hours per evening for the next 2 and a half weeks... You realize this right? I dunno anyone who can do that. You really think it'll take that long? I havn't bought anything yet, so if you could suggest someone who could make one, that would pretty much rock. Almost any fabrication shop or welding shop could make it for you. You'd have to speak with them and explain what it is your wanting. I have a set of BD 'poons in the basement. Give me a couple min to look at the center plates side by side so we're on the same page.
|
|
|
|
|
sungam
Oct 24, 2008, 5:15 PM
Post #28 of 36
(853 views)
Shortcut
Registered: Jun 24, 2004
Posts: 26804
|
the_climber wrote: sungam wrote: the_climber wrote: You know if you just had one made custom you wouldn't have to file the bar 2 to 3 hours per evening for the next 2 and a half weeks... You realize this right? I dunno anyone who can do that. You really think it'll take that long? I havn't bought anything yet, so if you could suggest someone who could make one, that would pretty much rock. Almost any fabrication shop or welding shop could make it for you. You'd have to speak with them and explain what it is your wanting. I have a set of BD 'poons in the basement. Give me a couple min to look at the center plates side by side so we're on the same page. I think that I'd only have to file a short section of them thinner (the plate fits through the front section, just not the back part), and I would saw off the unneeded section.
|
|
|
|
|
the_climber
Oct 24, 2008, 5:30 PM
Post #29 of 36
(850 views)
Shortcut
Registered: Oct 9, 2003
Posts: 6142
|
OK, so I compaired the plates from a set of BD Sabertooths to the plates on my beloved G14's newmatics. Man have I ever put a lot of wear and milage on those things. I think I remember you saying that you got the GSB G14's, correct? Now that I've had a better look at things... Alright this is what I would do given trying to make said BD center plate work. THe BD plate is about 0.5mm thicker than the stock Grivel plate. The top end of the BD center plate (end for front of the crampon) increases in width, and is ~0.5mm-1mm too wide. But I managed without any trouble to get it through the keeper slots on the front half of the Grivels up to the point at which the width increases. Go a head and file that down to a narrower profile. I had thought the thickness of the bar would be more of an overall problem, but it's not... except for one part. Try as much as I could the BD plate will not fit the back half of the G14's with the quick adjust in place. You will have to remove this and secure the plate to the back with a bolt. A bolt is more secure anyways and you wouldn't weaken the plate by thinning it out. I'm assuming that you only have one pair of boots that you can use these 'poons with, so the lack of easy adjustment shouldn't bother you. I had assumed you were going to have to thin down plate end to end, but that is not the case. Short version: -Get the BD plates -file the wide bit at the top by ~0.5mm-1mm -toss the quick/spring adjust from the back half of the poon into the parts bin and use a small bolt to attach the plat eto the heel piece.
(This post was edited by the_climber on Oct 24, 2008, 5:32 PM)
|
|
|
|
|
sungam
Oct 24, 2008, 5:35 PM
Post #30 of 36
(843 views)
Shortcut
Registered: Jun 24, 2004
Posts: 26804
|
Key plan about the bolt thing. Yeah, I just have the one pair of boots. Thank you, oh information guru. (side note- we have the same 2 sets of 'poons? BD Sabretooths and G14's?)
|
|
|
|
|
the_climber
Oct 24, 2008, 5:40 PM
Post #31 of 36
(842 views)
Shortcut
Registered: Oct 9, 2003
Posts: 6142
|
sungam wrote: Key plan about the bolt thing. Yeah, I just have the one pair of boots. Thank you, oh information guru. (side note- we have the same 2 sets of 'poons? BD Sabretooths and G14's?) No problem. Yes BD Sabretooths and G14's. I would trade the Sabretooths for a set of G12's with New-matic bindings in a heartbeat though.
|
|
|
|
|
chossmonkey
Oct 24, 2008, 7:20 PM
Post #32 of 36
(826 views)
Shortcut
Registered: Feb 1, 2003
Posts: 28414
|
the_climber wrote: OK, so I compaired the plates from a set of BD Sabertooths to the plates on my beloved G14's newmatics. Man have I ever put a lot of wear and milage on those things. I think I remember you saying that you got the GSB G14's, correct? Now that I've had a better look at things... Alright this is what I would do given trying to make said BD center plate work. THe BD plate is about 0.5mm thicker than the stock Grivel plate. The top end of the BD center plate (end for front of the crampon) increases in width, and is ~0.5mm-1mm too wide. But I managed without any trouble to get it through the keeper slots on the front half of the Grivels up to the point at which the width increases. Go a head and file that down to a narrower profile. I had thought the thickness of the bar would be more of an overall problem, but it's not... except for one part. Try as much as I could the BD plate will not fit the back half of the G14's with the quick adjust in place. You will have to remove this and secure the plate to the back with a bolt. A bolt is more secure anyways and you wouldn't weaken the plate by thinning it out. I'm assuming that you only have one pair of boots that you can use these 'poons with, so the lack of easy adjustment shouldn't bother you. I had assumed you were going to have to thin down plate end to end, but that is not the case. Short version: -Get the BD plates -file the wide bit at the top by ~0.5mm-1mm -toss the quick/spring adjust from the back half of the poon into the parts bin and use a small bolt to attach the plat eto the heel piece. Good thing you included a short version. I don't think anyone wants to read the long one.
|
|
|
|
|
the_climber
Oct 24, 2008, 7:36 PM
Post #33 of 36
(822 views)
Shortcut
Registered: Oct 9, 2003
Posts: 6142
|
chossmonkey wrote: Good thing you included a short version. I don't think anyone wants to read the long one. Good thing you quoted the whole thing so people couple read the long version again.
|
|
|
|
|
chossmonkey
Oct 24, 2008, 7:51 PM
Post #34 of 36
(817 views)
Shortcut
Registered: Feb 1, 2003
Posts: 28414
|
the_climber wrote: chossmonkey wrote: the_climber wrote: OK, so I compaired the plates from a set of BD Sabertooths to the plates on my beloved G14's newmatics. Man have I ever put a lot of wear and milage on those things. I think I remember you saying that you got the GSB G14's, correct? Now that I've had a better look at things... Alright this is what I would do given trying to make said BD center plate work. THe BD plate is about 0.5mm thicker than the stock Grivel plate. The top end of the BD center plate (end for front of the crampon) increases in width, and is ~0.5mm-1mm too wide. But I managed without any trouble to get it through the keeper slots on the front half of the Grivels up to the point at which the width increases. Go a head and file that down to a narrower profile. I had thought the thickness of the bar would be more of an overall problem, but it's not... except for one part. Try as much as I could the BD plate will not fit the back half of the G14's with the quick adjust in place. You will have to remove this and secure the plate to the back with a bolt. A bolt is more secure anyways and you wouldn't weaken the plate by thinning it out. I'm assuming that you only have one pair of boots that you can use these 'poons with, so the lack of easy adjustment shouldn't bother you. I had assumed you were going to have to thin down plate end to end, but that is not the case. Short version: -Get the BD plates -file the wide bit at the top by ~0.5mm-1mm -toss the quick/spring adjust from the back half of the poon into the parts bin and use a small bolt to attach the plat eto the heel piece.Good thing you included a short version. I don't think anyone wants to read the long one. Good thing you quoted the whole thing so people couple read the long version again. I do what I can.
|
|
|
|
|
EvilMonkey
Oct 28, 2008, 12:41 PM
Post #35 of 36
(796 views)
Shortcut
Registered: Mar 19, 2008
Posts: 195
|
find out what kind of metal they use (probably spring steel), get some, and get metal fabricator (welder) to make em to your specs. it's more of a pain in the ass than just buying some 'pons that fit your big-ass hobbit feet, but it's your best bet.
|
|
|
|
|
sungam
Dec 20, 2008, 3:37 AM
Post #36 of 36
(730 views)
Shortcut
Registered: Jun 24, 2004
Posts: 26804
|
Here's a BIG shoutout to wmfork for helping me out with some common sense on this one. I took off the springy thing, like he said, and used on of the provided bolts to hold the center bar in place. it gave me the extra inch and a half I needed, and now the poons fit GREAT. Wooohooo! Pimped out poons and boots, bring on CO. P.S. T_C... due to some funding miscalculations (Think monopoly's "bank error in your favor" style) I may have some left over cash when *may* be put aside, depending on ticket prices, to making an excursion further north. I really hope it comes to be.
|
|
|
|
|
|