|
unrooted
Feb 12, 2008, 4:15 AM
Post #1 of 28
(16947 views)
Shortcut
Registered: Mar 13, 2003
Posts: 840
|
What bolts do you like in limestone?
|
|
|
|
|
sbaclimber
Feb 12, 2008, 4:47 AM
Post #2 of 28
(16922 views)
Shortcut
Registered: Jan 22, 2004
Posts: 3118
|
Depends on the limestone.....
|
|
|
|
|
unrooted
Feb 12, 2008, 4:49 AM
Post #3 of 28
(16913 views)
Shortcut
Registered: Mar 13, 2003
Posts: 840
|
sbaclimber wrote: Depends on the limestone..... The kind worth bolting.
|
|
|
|
|
sbaclimber
Feb 12, 2008, 4:58 AM
Post #4 of 28
(16904 views)
Shortcut
Registered: Jan 22, 2004
Posts: 3118
|
unrooted wrote: sbaclimber wrote: Depends on the limestone..... The kind worth bolting. That still doesn't narrow it down much. You may think I am trying to be difficult, but here in NZ there is limestone so soft that any bolt is pretty much suspect (and yes, it is still worth climbing) and other stuff that is plenty hard enough to take 3/8" expansion bolts.
|
|
|
|
|
unrooted
Feb 12, 2008, 5:08 AM
Post #5 of 28
(16891 views)
Shortcut
Registered: Mar 13, 2003
Posts: 840
|
I don't really know yet, it will be in Jamaica, what would you suggest for medium hardness (for limestone)?
|
|
|
|
|
sbaclimber
Feb 12, 2008, 5:14 AM
Post #6 of 28
(16887 views)
Shortcut
Registered: Jan 22, 2004
Posts: 3118
|
unrooted wrote: I don't really know yet, it will be in Jamaica, what would you suggest for medium hardness (for limestone)? Medium hard for limestone would probably still mean glue-ins. You might get away with long 1/2" expansion bolts for routes that won't see a lot of traffic, but glue-ins are really going to make everyone happy for a lot longer. The good news is, if it really is medium hard and not soft, you should *only* need "normal" glue-ins, nothing exceptionally long or thick. Caveat, I don't have any personal experience bolting limestone. I have climbed on a lot of it, of widely differing qualities, both here an in Germany though.
|
|
|
|
|
miavzero
Feb 12, 2008, 5:21 AM
Post #7 of 28
(16877 views)
Shortcut
Registered: Oct 8, 2005
Posts: 624
|
Fixe 3/8''x4'' double expansion SS has served me well in Nevada limestone.
|
|
|
|
|
unrooted
Feb 12, 2008, 5:33 AM
Post #8 of 28
(16867 views)
Shortcut
Registered: Mar 13, 2003
Posts: 840
|
Where is the best place to buy them? They cost about $8 at gear shops right? Also I'm only finding 3.75" bolts.
|
|
|
|
|
miavzero
Feb 12, 2008, 5:38 AM
Post #9 of 28
(16865 views)
Shortcut
Registered: Oct 8, 2005
Posts: 624
|
I get them through a friend for about $5 each. I know REI used to carry them for a liile more.
|
|
|
|
|
rockjunkie2
Feb 21, 2008, 10:17 PM
Post #10 of 28
(16745 views)
Shortcut
Registered: Nov 14, 2006
Posts: 16
|
i never use limestone bolts
|
|
|
|
|
lithiummetalman
Feb 21, 2008, 10:52 PM
Post #11 of 28
(16713 views)
Shortcut
Registered: Feb 28, 2004
Posts: 286
|
Limestone is fun stuff... anyways used 1/2" X 3 1/2" concrete stud bolts reinforced with industrial grade concrete cement epoxy hope this helps! Peace
|
|
|
|
|
sbaclimber
Feb 21, 2008, 11:12 PM
Post #12 of 28
(16698 views)
Shortcut
Registered: Jan 22, 2004
Posts: 3118
|
lithiummetalman wrote: used 1/2" X 3 1/2" concrete stud bolts reinforced with industrial grade concrete cement epoxy Although not *necessarily* dangerous, this is not considered good bolting technique. If you are going to go through the trouble of using glue, then just do the job right. Glue works on the principal of proper contact over a surface area. Using an expansion (what I assume is meant by "stud") bolt with the glue simply reduces the chances that glue coverage is going to be correct. "reinforced" in this case is more than likely just a fallacy.
|
|
|
|
|
tolman_paul
Feb 22, 2008, 12:46 AM
Post #13 of 28
(16669 views)
Shortcut
Registered: Apr 22, 2005
Posts: 385
|
You can seal a bolt with epoxy, but jsut gooping epoxy in the hole and driving and tensioning a stud anchor isn't the same as a proper glue in. For a glue in you drill a hole typically 1/16" over the dia of the stud, either add a chemical "pill" that you mix as you drive and spin the stud in place, or use a two part glue that mixes in the nozzle as you put it in the hole and then set the stud. I'm pretty much going to 1/2" X 5 1/2" stud anchors for our local choss rock. With a power drill there is no reason not to place a large bolt in questionable rock.
|
|
|
|
|
lithiummetalman
Feb 22, 2008, 12:48 AM
Post #14 of 28
(16668 views)
Shortcut
Registered: Feb 28, 2004
Posts: 286
|
Good to know! Thanx! This was years ago, the fellow (he worked in construction) I worked with suggested using the epoxy cement as a filler once the bolt was in place and the usage of concrete stud bolts instead of expansion bolts. I still got a long ways of learning to go. any tips and advice much appreciated peace edited for clarity
(This post was edited by lithiummetalman on Feb 22, 2008, 12:49 AM)
|
|
|
|
|
chossmonkey
Feb 22, 2008, 1:06 AM
Post #15 of 28
(16653 views)
Shortcut
Registered: Feb 1, 2003
Posts: 28414
|
unrooted wrote: I don't really know yet, it will be in Jamaica, what would you suggest for medium hardness (for limestone)? Are they sea cliffs?
|
|
|
|
|
unrooted
Feb 22, 2008, 1:11 AM
Post #16 of 28
(16646 views)
Shortcut
Registered: Mar 13, 2003
Posts: 840
|
chossmonkey wrote: are they sea cliffs? No, they should be around 20-50 miles from the ocean, the sea cliffs will hopefully provide some good psychobloc.
|
|
|
|
|
chossmonkey
Feb 26, 2008, 4:32 PM
Post #17 of 28
(16554 views)
Shortcut
Registered: Feb 1, 2003
Posts: 28414
|
unrooted wrote: chossmonkey wrote: are they sea cliffs? No, they should be around 20-50 miles from the ocean, the sea cliffs will hopefully provide some good psychobloc. If it is medium hardness use at least 3/8"x3", it normally doesn't hurt to error on the side of a bit bigger or longer. Make sure to use stainless even though they aren't in a sea cliff. Most stainless bolts and hangers are 304 stainless. I think its 316 stainless you would need if it was near the ocean. If it is pocketed make sure to have a couple different lengths, sometimes a shorter bolt will be more secure than a longer bolt if it means the longer bolt is going through a pocket putting the expansion cone near an edge. The double clipped Fixe bolts would be the safest bet short of a glue-in.
|
|
|
|
|
unrooted
Feb 26, 2008, 4:51 PM
Post #18 of 28
(16532 views)
Shortcut
Registered: Mar 13, 2003
Posts: 840
|
chossmonkey wrote: If it is medium hardness use at least 3/8"x3", it normally doesn't hurt to error on the side of a bit bigger or longer. Make sure to use stainless even though they aren't in a sea cliff. Most stainless bolts and hangers are 304 stainless. I think its 316 stainless you would need if it was near the ocean. If it is pocketed make sure to have a couple different lengths, sometimes a shorter bolt will be more secure than a longer bolt if it means the longer bolt is going through a pocket putting the expansion cone near an edge. The double clipped Fixe bolts would be the safest bet short of a glue-in. I found these at Fixe's website: http://fixehardware.com/...e-grade_hardware.htm Do you know of any other sources for A-316 SS bolts?
|
|
|
|
|
koopatroopa
Feb 26, 2008, 6:00 PM
Post #19 of 28
(16502 views)
Shortcut
Registered: Jun 27, 2003
Posts: 7
|
what's the peace corps got to say about throwing bolts up while in the service?
|
|
|
|
|
chossmonkey
Feb 26, 2008, 6:04 PM
Post #20 of 28
(16500 views)
Shortcut
Registered: Feb 1, 2003
Posts: 28414
|
You can get the A-316 bolts from Hilti, Powers, ECT. but I think only Fixe makes 316 hangers. I think mixing the two could be bad in certain environments. I don't know enough about it to say for sure. Epoxy coated hangers like from Metoliuos might help protect the hanger as long as the coating doesn't get chipped.
|
|
|
|
|
unrooted
Feb 29, 2008, 1:31 AM
Post #21 of 28
(16399 views)
Shortcut
Registered: Mar 13, 2003
Posts: 840
|
how close is 'near the ocean'? Most of the rock would be inland several miles, do you think that would make 304 good enough?
|
|
|
|
|
sbaclimber
Feb 29, 2008, 2:14 AM
Post #22 of 28
(16383 views)
Shortcut
Registered: Jan 22, 2004
Posts: 3118
|
unrooted wrote: how close is 'near the ocean'? Most of the rock would be inland several miles, do you think that would make 304 good enough? All caveats apply of course, but chances are 304 would be fine. All really depends on the overall climate though. I've seen 10yr old SS bolts within spitting distance of the ocean that were in fine condition (overall sunny and dry conditions), and then there's Thailand style......less than 5yrs old and already turned to mank.
|
|
|
|
|
chossmonkey
Feb 29, 2008, 12:02 PM
Post #23 of 28
(16337 views)
Shortcut
Registered: Feb 1, 2003
Posts: 28414
|
sbaclimber wrote: unrooted wrote: how close is 'near the ocean'? Most of the rock would be inland several miles, do you think that would make 304 good enough? All caveats apply of course, but chances are 304 would be fine. All really depends on the overall climate though. I've seen 10yr old SS bolts within spitting distance of the ocean that were in fine condition (overall sunny and dry conditions), and then there's Thailand style......less than 5yrs old and already turned to mank. From what I've heard you can't really tell when a SS bolt is going bad, it just breaks. It seems I heard something about the 304 bolts at Camen Brac going bad as well. I think standard glue-ins made for reliable replacements to the mechanical bolts since they were isolated from the rock. Thailand is a whole different kettle of fish. As to the distance of the ocean, I have heard within 5 miles of the coast can be considered a marine environment for building materials and stainless (normally 304) should be used rather than plated steel. I would guess as long as you can't smell the ocean 304 stainless would be okay as far as climbing anchors go. That could be bad info though.
|
|
|
|
|
unrooted
Mar 4, 2008, 5:19 PM
Post #24 of 28
(16245 views)
Shortcut
Registered: Mar 13, 2003
Posts: 840
|
what do you think of fixe triplex bolts? they are cheaper than stainless rawls, and are removeable.
|
|
|
|
|
chossmonkey
Mar 4, 2008, 5:29 PM
Post #25 of 28
(16238 views)
Shortcut
Registered: Feb 1, 2003
Posts: 28414
|
unrooted wrote: what do you think of fixe triplex bolts? they are cheaper than stainless rawls, and are removeable. You need a 12mm drill bit. Other than that they work okay. If you are not planning to remove them and put in glue-ins use 10mm/3/8" hangers and put the flange of the sleeve between the rock and the hanger. They will likely be a bitch to remove installed like that, but there would be a slight chance that if the flange is between the hanger and the nut the whole installation could pull out if the nut loosened and there was an outward pull. You also may need to flare the opening of the hole very slightly to get the flange to sit all the way flush with the rock. If the hanger is not tight against the rock it will tend to want to spin.
|
|
|
|
|
|